Some computers use a special enclosure to secure the hard drive. If your hard drive has an enclosure for the hard drive, remove all the screws and pull the old hard drive out. Place the new hard drive in the same enclosure and secure it with the screws.
Insert your new drive. Place the hard drive in the hard drive slot the old hard drive was housed in, or the expansion slot for a new hard drive. Secure the hard drive. Once the hard drive has been inserted, use the screws that came with it to secure the hard drive in the housing.
Ideally, you should use two screws on each side of the hard drive. If the hard drive is loose, it can rattle and cause more noise and lead to physical damage. Tighten the screws to a firm tightness, but don't over-tighten as that may cause damage as well.
Attach the drive to the motherboard. Use a SATA cable to connect the hard drive to the motherboard. SATA cables can be connected in either direction. To install an M. Press down on the other end of the SSD and screw it to the motherboard. Refer to your motherboard documentation for detailed information for your motherboard.
Connect the power supply to the hard drive. Most newer power supplies have SATA power connectors, though older power supplies typically only have Molex 4 pin connectors. Ensure that none of the cables can come undone by wiggling them a little bit. Close up your computer. Replace the case sides and reconnect your cables if you had to move the case to work on the inside.
Plug back in and turn back on your computer. You should hear the hard drive begin to spin up. If you hear beeps or any jarring noises, immediately turn off the computer and check the hard drive's connections. Install an operating system. Empty hard drives require an operating system to be installed on them before you can use your computer again. Method 2. Back up your laptop's information. If you're replacing a laptop's hard drive, you'll want to back up the information that's on the hard drive so that you can restore it onto the new hard drive later.
Make sure you can add or replace the hard drive in your laptop. Before you purchase a new hard drive for your laptop, check the user's manual or open your laptop to make sure you can replace or install a second hard drive. The majority of laptops do not have an expansion slot to install a second hard drive. Buy a hard drive that matches your model of laptop. Most modern computers and laptops use SATA drives. Search for a hard drive that works with your model of computer, then purchase your preferred option.
Most laptops use a 2. Some newer laptops use M. Turn off your laptop. Disconnect your laptop from its charger, then press and hold the Power button until the laptop turns off. You can also use the laptop's Power settings to turn it off: Windows - Click the Windows Start menu, click the power icon, and click Shut down.
Mac - Click the Apple icon in the menu bar, click Shut Down Turn over your laptop. Shut your laptop's lid, then flip it over so that the bottom of the laptop is facing up. Remove the bottom of the laptop. This will vary from laptop to laptop, but you'll usually need a screwdriver to remove the case.
Use a plastic pry tool to carefully go around the edges of where the bottom panel is attached to the keyboard and carefully pry it loose. Many laptops require special screwdrivers, such as Pentalobe models, or tri-wing screwdriver, to unlock the case.
Some laptops, such as Mac laptops, will require you to unscrew several screws around the border of the case. Be careful of any ribbons or cables attached to the motherboard from the bottom panel. If you find any cables or ribbons attached, make a note of where they are attached, and carefully remove them.
This will prevent you from accidentally harming your computer's delicate internals with static electricity. You can ground yourself by touching something metal or by purchasing static wrist bands that you wear while you work on your computer.
Remove the battery if possible. Most laptops will allow you to remove the battery, which will prevent you from inadvertently shocking yourself during the hard drive installation.
Open the hard disk panel if present. On some laptops, the hard drive may be housed inside a special panel. The panel can usually be identified by the hard drive logo printed next to it.
You will usually need a small Phillip's head screwdriver in order to remove the screws and the panel. Unscrew the hard drive. Depending on the laptop, the hard drive may be secured in place with screws.
Remove all screws holding the laptop in place. Remove the existing hard drive if necessary. Slide it out from the connection port that it is attached to. There may be a release latch or ribbon you pull to disconnect the hard drive. The hard drive will pop back about half an inch, allowing you to remove it from its housing. You may also need to disconnect your hard drive from a wire or cable. It's best to place your old hard drive somewhere safe in case you need to retrieve data off of it.
Insert your new hard drive. Ensure that you insert it with the correct side facing out, then press it firmly into the connectors. Do not force the hard drive, or you may damage the connectors. Step 3: Fasten the second hard drive into a hard drive caddy tray for optical drive slot. Step 4: Remove the baffle from the optical drive tray and install it on the hard drive caddy tray.
Step 5: Insert the hard drive caddy tray into the optical drive bay and screw the two fasteners unscrewed previously. Step 2: Remove the front cover of the chassis by unscrewing two fasteners shown in the following picture, and then nudging the cover to the side. Step 3: Remove the hard drive bracket from the chassis and fasten the hard drive into it.
Step 5: Plug in the power and data lines, with one end into the hard drive and the other end into the slot built in the chassis. After physically installing a second hard drive, you may wonder how to install it in Windows For that, you should initialize the hard drive, create new partitions, and format the new partitions.
Step 2: For the newly installed hard drive, the system will automatically pop up the prompt to initialize it. The pop-up window looks like the following one. Try solutions here to fix it. Step 1: Right-click the black unallocated space and choose New Simple Volume. Follow the wizard to create a new partition. Step 2: Right-click the new partition to choose Format. Then, uncheck Perform a quick format to run a full format, which will automatically check the hard drive to fix some errors.
This article explains quick format, full format and the difference between them. It also touches upon the problems: how to recover data from quick formatted disk, and how to make data unrecoverable. You can also complete the above process through MiniTool Partition Wizard. It is a professional partition management software. How to get to Disk Management Windows 10 for disk or partition management? This post shows you much on disk management Windows Here is a step-by-step guide on how to install a second hard drive in your laptop and desktop PC.
If you are planning to do that, I think you may need this tutorial. Click to tweet. Do you have any problems in installing a second hard drive? Please leave a comment below. If you have problems with data backup or disk management, please also leave a comment below or email us at [email protected].
We will reply to you as soon as possible. To make your computer recognize the second hard drive, you should initialize the hard drive through the following steps:. Download Partition Wizard. Summary : Do you know how to install a second hard drive in the laptop or desktop PC? Tip: If your PC doesn't have an extra hard drive bay, but it has an optical drive bay, it still can install a second hard drive. It is able to copy the operating system, applications as well as all kinds of files to the new drive.
Enjoy high speed of SSD. Wide compatibility. You can finish data transfer between two drives with a few clicks. After the cloning process is complete, you can remove the old hard drive and install the new drive as mentioned above. Your laptop will be usable immediately. Now you know how to replace laptop hard drive and reinstall operating system exactly.
Share this page with your friends if you think it's helpful. Need to replace laptop hard drive No matter you are using a laptop or a desktop, you may need to perform hard drive replacement sometimes. How to replace laptop hard drive and reinstall Windows 10?
Then, follow the instructions below: Stage 1: Remove the old drive Make sure your laptop is turned off and unplugged before starting, and then follow the steps below: 1. Open the computer case.
Locate the hard drive and remove the power cable and data connector from the drive itself. Remove the screws and pull out the old hard drive. Stage 2: Install the new drive To put the new drive in, you can simply reverse the steps you already performed in Stage 1.
Take Windows 10 as an example: 1. Insert Windows 10 installation media and boot from it.
0コメント